Pilot-RC 1/5 P-47D Thunderbolt 2.41M (95") Composite Nitro Warbird (Video shown flying with Saito 90R3 radial four stroke engine)
Overview
Presenting Pilot-RC’s first composite scale warbird! It could be no other than the fantastic P47, specifically, the P47D variant.
With its instantly recognisable lines and large wing for friendly handling it is ideal both as crown jewel and everyday hack.
Designed around popular engine sizes, we have tested our P47D both with the straight forward single cylinder DA85, and also with the more scale like three cylinder Saito 90R3 with outstanding results.
Needing a very short takeoff roll, and no wing waggle, this model will inspire confidence from day one.
Features
Full scale detail with rivets, panel lines, simulated hatches, etc…
Full composite construction, lightweight and strong
Two piece wing and two piece stabilizer, all for easy transport
Painted outside the mold so no seam lines
Fully hidden linkages except rudder horn. No other horns, servo arms, ball links or pushrods are exposed
Battery support included, allows for the mounting of batteries to the inside of the firewall to easily help achieve the correct center of gravity
Patented quick assembly system for wings
The cowl can fit Satio 90R3 (or other similar 250mm diameter radial engines)
50-85cc single cylinder two stroke engine is also easy to install
Removable engine box can fit different engine
Ample room to easily install canisters if desired
Elevator and rudder servos mounted mid-fuselage to avoid the need for nose weight
A single rudder servo controls both rudder and tail wheel, both by pull pull system
Tail gear door operates (open/close) without need of a dedicated servo
Single servo controls both elevator half
Specifications
Wing Area
1,685"2 (10,870cm2)
Weight
40.7lbs (18.5kg) with Saito 90R3 engine, electric starter and all accessories
Included Hardware
- Complete air frame (including aluminium wing-tubes and fibreglass control horns)
- Servo extension leads
- Fuel tank (700ml) and fuel tubing pre-prepared, fuel dot and breather valve
- Pre-prepared pushrods with ball links
- Pre-glued and painted control horns
- Two simulated bombs and their brackets. Can be dropped individually. The brackets can be attached or removed two bolts each. Please note that if intending to release the bombs in flight, these will first need to have extra ballast added to them.
- Simulated drop tank, easily installed using a single bolt
- Scale antenna included
- Center of Gravity measurement system included
Optional Extras
- Additional scale aluminium spinner for different engine
- Wingbags
- Navigation light system (Controller and LEDs)
- Electric starter set for Saito 90R3. Includes starting controller, kill switch, scale aluminium spinner, brushless motor and all gearings. (Can also be adapted to other engines, contact us for more information)
- Two stroke gas engine adapter kit. Includes engine box (standoff), wood plate for mounting any necessary ballast, scale aluminium spinner and pre-cut cowl baffle for optimum engine cooling
- Custom built canister with scale exhaust, for DA85, GP88 and DLE85. Includes canister, header and mounting accessories
Required Hardware
- Two stroke motor: 50-88cc or
- Four stroke motor: 80cc or similar size radial engine
- Servos: x9 (+2 optional)
- x2 Super high torque (minimum 40kg). Uses x1 per flap
- x4 High torque (minimum 27kg). Uses x1 per aileron, x1 for elevator, x1 for rudder
- x3 Mid size servo (35x15x30mm). Uses x2 for the gear doors and x1 for throttle
- +2 Optional mid size servo (35x15x30mm) for the bomb drop
- Also requires all the usual accessories such as transmitter, receiver, batteries, powerbox and possibly other small accessories
Recommended Hardware
- Servos: Pilot-Rc PW48AH (48Kg – 0,1s at 8,4v)
- Servos: Pilot-Rc PW28AH (28Kg – 0,056s at 8,4v)
- Servos: Pilot-Rc PW16AH (16Kg – 0,057s at 8,4v)
- Servos: Pilot-Rc PY10AH (13Kg – 0,19s at 7,4v)
- Servo arms: Pilot-Rc 0.8-1.2" Aluminium arms (included with Pilot-Rc servos)
- Wingbags: Pilot-RC P47 Wingbags
Build Info
CONTROL THROWS
Travel each way
Aileron
9mm up / 13mm down (measured at the wingtip)
Elevator
30mm up / 30mm down (measured from the back edge of the elevator)
Rudder
Maximum deflection left and right
Take-off Flap
28mm (measured from the wing root side of the flap)
Landing Flap
67mm (measured from the wing root side of the flap)
Center of Gravity
140mm back from the leading edge on the root of the wing
Package & Build Options
Choose one of following Package Options from the drop-down menu
ARF PRO
- Complete air frame (including aluminium wing-tubes and fibreglass control horns) - pre-installed gear doors, cockpit, drop tank, bomb brackets and bombs
- Pilot-RC electric retracts specific for this model pre-installed
- Servo extension leads
- Fuel tank (700ml) and fuel tubing pre-prepared, fuel dot and breather valve
- Pre-prepared pushrods with ball links
- Pre-glued and painted control horns
- Two simulated bombs and their brackets. Can be dropped individually. The brackets can be attached or removed two bolts each. Please note that if intending to release the bombs in flight, these will first need to have extra ballast added to them.
- Simulated drop tank, easily installed using a single bolt
- Scale antenna
- Center of Gravity measurement system
- Scale cockpit set (without pilot figure)
- Required Servos: x9 (+2 optional)
- x2 Super high torque (minimum 40kg). Uses x1 per flap
- x4 High torque (minimum 27kg). Uses x1 per aileron, x1 for elevator, x1 for rudder
- x3 Mid size servo (35x15x30mm). Uses x2 for the gear doors and x1 for throttle
- +2 Optional mid size servo (35x15x30mm) for the bomb drop
- Required Engine: Two Stroke Motor (50-88cc) or Four Stroke Motor (80cc or similar size radial engine)
- Required all the usual accessories such as transmitter, receiver, batteries, powerbox and possibly other small accessories
- *Does not include spinner (Appropriate scale spinner can be purchased)
PNP (Engine Ready)
- Complete air frame (including aluminium wing-tubes and fibreglass control horns) - pre-installed gear doors, cockpit, drop tank, bomb brackets and bombs
- Pilot-RC electric retracts specific for this model pre-installed
- Servo extension leads
- Fuel tank (700ml) and fuel tubing pre-prepared, fuel dot and breather valve
- Pre-prepared pushrods with ball links
- Pre-glued and painted control horns
- Two simulated bombs and their brackets. Can be dropped individually. The brackets can be attached or removed two bolts each. Please note that if intending to release the bombs in flight, these will first need to have extra ballast added to them.
- Simulated drop tank, easily installed using a single bolt
- Scale antenna
- Center of Gravity measurement system
- Scale cockpit set (without pilot figure)
- Navigation light system - pre-installed
- Bomb drop system - pre-installed
- Wing bags
- 11X Pilot-RC servos and multi-wire connectors (for aileron, flap, retract, nav lights, and bomb drop), all pre-installed
- Required Engine: Two Stroke Motor (50-88cc) or Four Stroke Motor (80cc or similar size radial engine)
- Required all the usual accessories such as transmitter, receiver, batteries, powerbox and possibly other small accessories
- *Does not include spinner (Appropriate scale spinner can be purchased)
|
